Introduction
If you've purchased an Android Register and want to set it up, look no further! This guide will walk you through the steps on setting up your Register.
Let's get started!
Note: The information in this article can also be found here.
Choose the Android POS Register(s) you own from the list below:
Android Sunmi T2 Lite
Android Sunmi T2
Android Sunmi D2
Android Sunmi 12C
Android Sunmi T2 Lite
Set Up Register
Step 1.
When unboxing the Register, take out the adapter and wire. Connect the small wire head to the circular power port below:
Diagram for Sunmi T2 Lite:
Step 2.
On the side of the device's main large screen, you'll see the power button.
Turn it on by holding the power button for about 1-2 seconds.
Diagram for Sunmi T2 Lite:
Step 3.
Once turned on, you'll see the main screen of the Android Register. Be sure to Activate your Register if you have not done so already.
Step 4.
Next, go to the StoreHub app on your Android Register.
Go to the Menu > Settings > Printer.
Step 7.
Toggle Always Print Receipt ON.
If you have an external printer connected to your Register via USB, tap Search Printer, then tap the Printer once you see it on the screen.
Step 8.
After tapping on your printer name, toggle Receipt ON. Next, tap the ellipses icon (...)
Finally, choose Print Test Receipt:
Step 9.
Your printer should print a test receipt!
Connecting a Cash Drawer
If you've also purchased a cash register and want to link it to your Android Register, setting it up is easy!
Take the RJ11 / phone cable that comes with the cash drawer and attach it to the port as below:
Diagram for Sunmi T2 Lite:
Connecting a Barcode Scanner
Similarly, if you've purchased a barcode scanner to be used with the Android Register, setting that up is easy too!
To connect the barcode scanner, attach the scanner to either of the USB ports:
Diagram for Sunmi T2 Lite:
----------
Android Sunmi T2
Set Up Register & Built-in Printer
Step 1.
When unboxing the Register, take out the adapter and wire. Connect the small wire head to the port below:
Diagram for Sunmi T2:
Step 2.
On the bottom right of the device, you'll see the power button.
Turn it on by holding the blue power button for about 1-2 seconds.
Diagram for Sunmi T2:
Step 3.
Once turned on, you'll see the main screen of the Android Register. Be sure to Activate your Register if you have not done so already.
Step 4.
Next, go to the StoreHub app on your Android Register.
Go to the Menu > Settings > Printer.
Step 7.
Toggle Always Print Receipt ON.
If you're using the built-in printer with your Android POS, tap Built-in Printer, then choose Receipt.
Step 8.
Tap the ellipses icon (...) and choose Print Test Receipt:
Step 9.
Your printer should print a test receipt!
Connecting a Cash Drawer
If you've also purchased a cash register and want to link it to your Android Register, setting it up is easy!
Take the RJ11 / phone cable that comes with the cash drawer and attach it to the port as below:
Diagram for Sunmi T2:
Connecting a Barcode Scanner
Similarly, if you've purchased a barcode scanner to be used with the Android Register, setting that up is easy too!
To connect the barcode scanner, attach the scanner to either of the USB ports:
Diagram for Sunmi T2:
----------
Android Sunmi D2
Set Up Register
Step 1.
When unboxing the Register, take out the power adapter and wire. Connect the small wire head to the circular port below:
Diagram for Sunmi D2:
Step 2.
On the bottom of the device, you'll see the power button.
Turn it on by holding the blue power button for about 1-2 seconds.
Diagram for Sunmi D2:
Step 3.
Once turned on, you'll see the main screen of the Android Register. Be sure to Activate your Register if you have not done so already.
Step 4.
Next, go to the StoreHub app on your Android Register.
Go to the Menu > Settings > Printer.
Step 7.
Toggle Always Print Receipt ON.
If you have an external printer connected to your Register, tap Search Printer, then tap the Printer once you see it on the screen.
Step 8.
After tapping on your printer name, toggle Receipt ON. Next, tap the ellipses icon (...)
Finally, choose Print Test Receipt:
Step 9.
Your printer should print a test receipt!
Connecting a Cash Drawer
If you've also purchased a cash register and want to link it to your Android Register, setting it up is easy!
Take the RJ11 / phone cable that comes with the cash drawer and attach it to the port as below:
Diagram for Sunmi D2:
Connecting a Barcode Scanner
Similarly, if you've purchased a barcode scanner to be used with the Android Register, setting that up is easy too!
To connect the barcode scanner, attach the scanner to either of the USB ports.
----------
Android Sunmi 12C
Set Up Register & Built-in Printer
Step 1.
When unboxing the Register, take out the adapter and wire. Connect the small wire head to the port below:
Step 2.
On the bottom right of the device, you'll see the blue power button.
Turn it on by holding it for about 1-2 seconds.
Step 3.
Turn on the attached receipt printer by holding down the button on the right for about 3-5 seconds.
The green light (left) will appear, then the red light (right) will light up when powered on:
Step 4.
Once turned on, you'll see the main screen of the Android Register. Be sure to Activate your Register if you have not done so already.
Step 5.
Now it's time to set up the built-in printer.
Open the highlighted latch by pulling it down gently. Place your receipt roll so that the loose part is at the top of the roll.
Step 6.
Next, go to the StoreHub app on your Android Register.
Go to the Menu > Settings > Printer.
Step 7.
Toggle Always Print Receipt ON.
Tap Built-in Printer, then choose Receipt.
Step 8.
Press the ellipses icon (...) and choose Print Test Receipt:
Step 9.
Your printer should print a test receipt!
Connecting a Cash Drawer
If you've also purchased a cash register and want to link it to your Android Register, setting it up is easy!
Take the RJ11 / phone cable that comes with the cash drawer and attach it to the port that says CASH:
Connecting a Barcode Scanner
Similarly, if you've purchased a barcode scanner to be used with the Android Register, setting up is easy too!
To connect the barcode scanner, attach the scanner to either of the USB ports found at the side of the printer (where the Power On/Off button is).
Comments
0 comments
Please sign in to leave a comment.